Home > Driver For > Driver For Device Eth1 Has Been Compiled With Version

Driver For Device Eth1 Has Been Compiled With Version

it wasn't inverting everything, but that was no good. The "Set Mode" error is harmless. rmmod airo gets rid of it, and afterward ifup works. Thanks /sbin/iwlist eth1 scan Warning: Driver for device eth1 has been compiled with version 20 of Wireless Extension, while this program supports up to version 19. check here

Welcome to the most active Linux Forum on the web. I have to run 'modprobe bcm43xx-mac80211' and 'ifup eth1' to get an actual network connection. Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs Home Forums HCL Reviews Tutorials Articles Register Search Search Forums Advanced Search Search Tags Search LQ Wiki Search Tutorials/Articles Search But how can I use VPNC after setting up my wireless.

Note that registered members see fewer ads, and ContentLink is completely disabled once you log in. Rebooted and installed everything again. Giving up for the night. For more advanced trainees it can be a desktop reference, and a collection of the base knowledge needed to proceed with system and network administration.

I tried to illustrate the situation with the output below. Warning: Driver for device eth1 has been compiled with version 22 of Wireless Extension, while this program supports up to version 20. It subsequently works. Any advice would be appreciated.Error for wireless request "Set Bit Rate" (8B20) : SET failed on device eth1 ; Invalid argument.Determining IP information for eth1...

However, bcm43xx-fwcutter had not been upgraded and would not handle the new drives. So it appears that my card is working in the sense that it detects my school's wireless networks, now I just need to activate it somehow. Some things may be broken... So I remove any thing related to ipw1394 (not ieee80211 ).

Some things may be broken..." installed wireless-tools-27-0.pre25.3 2.6.10-1.770_FC3 NetworkManager-gnome-0.3.4-1.1.0.fc3 NetworkManager-0.3.4-1.1.0.fc3 I have kept this PC updated So why the error? Fails to obtain an IP and is listed as unconnected. But always ... #Connect: Network is unreachable. So I use add/remove software to add networkmanager relative stuff.

Some things may be broken... https://forums.gentoo.org/viewtopic-t-576309-start-0.html but I still can't connect to an access point. typing #ps -C ipw3945 PID TTY TIME CMD #/sbin/ipw3945d ipw3945d - regulatory daemon Copyright (C) 2005-2006 Intel Corporation. I have all the updates for 5.I have gone to intellinuxwireless and have downloaded the iwlwifi-1.0.0-1 and installed the RPM successfully.When I try to load the driver I get:[[email protected] iwlwifi-1.0.0-1]# ./load./unload:

Click Here to receive this Complete Guide absolutely free. pop over to these guys However, I can scan the spectrum with "iwlist scan". -- Greetings Bertho Comment 2 Bertho 2005-10-23 14:27:00 EDT Upgrading to wireless-tools-28-0.pre10.4 from update testing works for me. Actual Results: Everything appears to work as before, but I also get the above error message. Some things may be broken...

I am also filing a report with glibckernheaders which should be updated as well. From 192.168.1.25 icmp_seq=2 Destination Host Unreachable From 192.168.1.25 icmp_seq=3 Destination Host Unreachable --- 192.168.1.1 ping statistics --- 3 packets transmitted, 0 received, +2 errors, 100% packet loss, time 2008ms , pipe Offline #3 2005-10-03 11:40:22 sml Member Registered: 2005-05-21 Posts: 89 Re: Centrino Wireless ipw2200 failure after the 1 Oct Upgrade Ok. http://alpinedesignsmtb.com/driver-for/driver-for-device-ra0-has-been-compiled-with-version-20.php Any help is greatly appreciated.

It seems like there is a timing or order issue. or I really have to input something by using windows XP to scan available network. Many Thanks kokomo View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by kokomo Thread Tools Show Printable Version Email this Page Search

iwconfig shows some weird "devXXXXX" device that is not associated with an ethX name.

ESSID and keys are correct. iwconfig eth1 2. 3. Is this correct? I got it from fc3.

I tried to reactive wireless by system-config-network of my eth1. (eth0 is wired network) It shows Determining IP information for eth1... Thanks. Warning: Driver for device eth1 has been compiled with version 22 of Wireless Extension, while this program supports up to version 20. my response Join Us!

In the very beginning, I followed garfield1228's procedure and it works.. eth1 Recommend Wireless Extension v16 or later, Currently compiled with Wireless Extension v18. Thanks kokomo View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by kokomo 08-18-2006, 12:32 PM #6 2Gnu Senior Member Registered: Jan Some things may be broken...

Does that help the problem at all? Some things may be broken... Some things may be broken...